The so-called ring winding machine function program test method is the winding machine CNC system of common functions and important special functions, such as zeroing, angle, positioning, forward and reverse, speed setting, fixed cycle, user macro program, etc. with manual programming or automatic programming methods, the preparation of a functional test program, and then start the CNC system to run this functional test program.

The function program can be used to check the accuracy and reliability of the specific execution of these functions of the ring winding machine, so as to quickly determine which function of the system is not good, and then determine the possible cause of the failure. This method is a better way to determine the failure of a winding machine for long term lack of maintenance and long term idle CNC winding machines and for checking when the machine is turned on for the first time and when the red wire machine causes a lot of scrap but no alarm, and it is difficult to determine for a while whether it is due to a programming or operation error or an automatic winding machine failure. And it can run the function test program several times continuously to diagnose the system operation stability of the whole winding machine.

Most modern automatic winding machine its CNC system modular design, divided into different modules according to the different functions, with the development of modern CNC technology, the integration of the circuit is becoming larger and larger, the technology is also becoming more and more complex, according to conventional methods, it is difficult to locate the fault in a very small area, and once the system failure using this method can shorten the downtime, quickly find the automatic winding machine fault trigger.

There are many customers in the purchase of winding machine is not very understanding of its settings and use, our engineers to provide you with the following tips for your reference.

First of all, we must have a good understanding of the characteristics of the wire type of the skeleton, the number of turns and the appearance of the material, winding speed: 1.

1, such as self-adhesive wire, enameled wire, etc., the set wire diameter should be increased a lot, because the outer skin is not too smooth, more inertia-free characteristics.

2、細いワイヤーの巻き取り速度は、遅すぎてはいけないが、ワイヤーを引き剥がさないように、ゆっくりとした上昇で開始しなければならない。

3、太い線があまりにも高速（速度以上）であってはならないが、低中速トルクが十分であることに注意を払う必要があります。

4、アルミ線の使用は、アップ力が銅線よりも同じ厚さに調整する必要があることに注意してくださいはるかに小さいので、製品の品質に影響を与え、外側の絶縁塗料が破裂し、薄い線径を引っ張らないように。

5、アップ力の減少に起因するアルミ線の使用は、設定された線径が適切に増加すべきである。自分のアップフォースニーズと組み合わせることで、ワイヤーホイールの上に少ない行くことができます。

第二に、骨格の形状とワイヤーの高さ、ラインからの距離にはかなりの関係がある。

1、正方形の骨格のスピードが速すぎない、真ん中は丸い凸凹があり、ラインにきちんと影響を与える。

2、スケルトンとラインアレンジャーの高さが適切であること、低すぎるラインは次の層に落ちやすく、高すぎるとジャンプライン現象が発生します。

3、ワイヤーラインと骨格の間の距離が遠すぎてはいけません、カップリングとラインの精度に影響を与えます。

4、ワイヤーのラインアウトが緩くなり、巻線とラインアップが美しいかどうかも関係しています。

Third, the automatic winding machine setting notes.

1、骨格の幅と巻き始めの校正が最優先であり、最も重要である。

2, when the starting winding point is correct, start winding, available at both ends of the parking first test the set width

Whether the correct width.

3, when starting transformer winding machine, if the following conditions occur, the causes can be identified according to the following.

If the winding point is too far ahead or too far behind: It may be that there is no vertical phenomenon at the wire outlet and the skeleton.

The wire arrangement is too sparse or too dense: it is usually caused by incorrect wire diameter setting.

Transformer winding machine ends rotate too fast or too slow: incorrect width setting: too fast = not wide enough, too slow = too wide.

Line with the coupling whether faster and faster or slower and slower: then fine-tune the size of the wire diameter, faster and faster = change small, slower and slower = change large. Pay attention to the transformer winding machine after winding several layers of the line with the coupling situation.

WhatsApp/ウィチャット+86 13075286997

メール： sales@vacuz.com